How to read a tractor tire size
480/70R38, 16.9-30 8PR, 14.9R28… what the markings on a tractor tire mean.
- The last number is always the rim diameter in inches.
- R means radial; a dash means bias construction.
- In radial sizes the first number is width in mm, the second the aspect ratio.
- Load index and speed symbol are written next to the size.
Radial metric sizes: 480/70R38
- 480 – section width in mm.
- 70 – aspect ratio (sidewall height as % of width).
- R – radial construction.
- 38 – rim diameter in inches.
A code such as 141A8 follows: 141 is the load index, A8 the speed symbol (40 km/h).
Bias-ply sizes: 16.9-30 8PR
- 16.9 – width in inches.
- - – bias (cross-ply) construction.
- 30 – rim diameter in inches.
- 8PR – ply rating; higher means more load capacity and pressure.
Mixed: 14.9R28 and 380/85R28
14.9R28 is a radial with an inch width; on the same rim it has almost the same outside diameter as 380/85R28. See the radial ↔ bias-ply equivalents table.
If unsure, take a photo of the sidewall of your current tire.
Older size formats
Some older tractors show sizes with two widths, such as 12.4/11-28 or 13.6/12-38. The first number is the newer designation and the second the older one; both describe the same tyre, and the last number is still the rim diameter. Dealers usually use the first number (12.4-28).
Why the rim diameter matters most
Width and sidewall height can vary between options, but a tyre only fits a rim of the same diameter. A 16.9-30 will not go on a 28-inch rim. So when reading a size, look at the last number first. If you are thinking of switching to a different size, first ask whether the rim can stay the same.
Outside diameter and rolling circumference
The outside diameter can be estimated from the size, but tyres of the same size can differ by a few centimetres between makers. Diameters shown on this site come from manufacturer tables where available; estimated values are marked with ≈. On 4WD tractors this difference matters for the front–rear ratio.
Common mistakes
- Confusing width with rim size: in 16.9-30, 16.9 is the width and 30 the rim.
- Ignoring the series: 480/70R38 and 480/80R38 share a width but not a diameter.
- Skipping the load code: the same size comes in different load indices; check the maker's load–pressure table.
Practical tips when noting a size
Before visiting the dealer, write the size exactly as it appears on the sidewall, with all letters and symbols. Leaving out the “R”, the dash or the slash can lead to the wrong tyre. Note the load index and speed symbol too. On a 4WD tractor record front and rear sizes separately; they form a pair and their ratio matters. If you can, take a photo of the sidewall so the dealer can also see the tread pattern. If a size is unfamiliar, type it into the search box on this site to see which tractors use it and what its equivalents are. That gives you something to compare against if you consider changing size.
Frequently asked questions
What does the last number in a tyre size mean?
It is the rim diameter in inches. A tyre only fits a rim of the same diameter, so read this number first.
What does 70 mean in 480/70R38?
It is the series or aspect ratio: sidewall height as a percentage of section width.
Are 14.9R28 and 14.9-28 the same tyre?
Width and rim are the same but construction differs: R is radial, the dash is bias. Do not mix them on one axle.
The sidewall is unreadable. What now?
Check the operator's manual or the manufacturer's spec sheet, or search your model on this site to see factory sizes with their source.
Published: 2026-09-25 · Updated: 2026-11-13
Guides
- Radial vs bias-ply tractor tires
- Front/rear tire ratio on 4WD tractors
- What pressure should tractor tires run at?
- What do the markings on a tractor tire sidewall mean?
- How to choose tires for a tractor trailer
- Narrow tires for orchard and row-crop tractors
- How to make tractor tires last longer
- When should tractor tires be replaced?
- Tractor ballast: weights and liquid ballast
- Radial vs bias tractor tyres
- Tractor tyre tread codes: R-1, R-1W, R-2, R-3, R-4, F-2, I-1
- Rim width and tyre fitment
- How to store tractor tyres and prepare for winter
- What to do when a tractor tyre goes flat
- Load index and speed symbol on tractor tyres
- How to tell a tyre's age (DOT code)
- Why do tractor front tyres wear fast?
- What is tractor track width and how is it adjusted?
- What to check when buying tractor tyres